might try these
http://atwoodperformance.com/
http://www.dyno-power.com/

or you can send them to a few of the sponsers here I have read about I have not had the opportunity to use any of them just getting my info and parts together right now.

LoneEagle

 

P/S, Whereabouts you live near Dayton? I live in Beavercreek and was thinking about Atwood. Also looking for a good power commander tuner as well

 

I live in Troy, about 25 minutes North of Dayton.

 

Ever go to Jackass Flats??

 

I'm also looking for a tuner.

 

Been there once. Holy $hit there is a lot of bikes. Wednesday is bike night.

 

I think there is one down close to cinci, I have to check into it. Trying to stay away from the steelers, otherwise F&S here in dayton does PC work.

 

Yup, go about every wed, lotta lot lizards too

 

Heard some bad things about F&S. Not sure if they are true or not.

 

These people are in Cincinnati

http://www.emcv2.com/

Don't know if they do boring but would know who does near by if they don't.

 

Atwood is a sponser here...but i read a post of his saying he only does heads right now...of which i've heard good things about...


he's around Columbus...I'm sure he would know of a reputable place...

 

Atwood is a sponser here...but i read a post of his saying he only does heads right now...of which i've heard good things about...


he's around Columbus...I'm sure he would know of a reputable place...

Last I talked with Arn he was only doing heads. But he would know who does boring in Ohio.

 

Anyone know where I could get my cylinders bored close to Dayton, OH? Just trying to save packaging time and waiting to ship there and back.
:thanks:

You know. You might want to checkout HDWrench with the 98" kits that he sells. go to www.gmrperformance.com and send him an email about what he has to offer.

 

Don, Your parts are on the way !!!!!!! Should be a fun ride without a doubt the cam will make some great power arcoss the board for you.

 

had my bike tuned at f&s was a waste of 300.00 said he couldnt get the pinging out between 2000 and 3000 rpms told me there it would ping a little on the ride back home to indiana i thought it was going to blow called him up and he told me to go into the timing table and put -4 in some of the tables still didnt help i had to use racing fuel mixed with 93 octane..........so would i take my bike there again (nope)

 

I know that the Carquest store in Richmond, IN on the west side has a machine shop that bores cylinders. I also know that they have the torque plates to do it with. But I don't know how good they are. I used to work there when it was Rodefelds. Back then it was a really good machine shop but I don't know anymore. Their number is 765-966-1571. If you call them ask for Doug in the machine shop. Store manager is Duane McDonald. Both very nice people. That would only be about a 45 min. drive for you. Also you might try Kopp Cycles in Batesville, IN, a little farther drive and I don't know for sure that they do boring, but they are extremely nice people and a power commander tuning center. I've heard good things about them.
www.koppcycles.com

 

Smyths automotive machine shop in West Chester (about 30min from you) can bore youy cylinders. They have all the torque plates, etc.

 

Dyno-Power is near Toledo and I would think they could help you. If not, you might give Bill Bishop a call and make the drive to Detroit.

 

Why mess around when you can send them to Wiesco. You can buy new pistons from them and they will bore the cylinders to match. They're in Mentor OH, just east of Clev.

Tim

 

Bore Tech in Batavia,Ohio 20miles east of ciny.They just list evo's on their web page but they do twin cams too.
http://www.bore-tech.com/index.htm